
 
 
 
 
 ĿĿ  ĿĿĿ Ŀ Ŀ Ŀ Ŀ  Ŀ
   ڿ  Ŀ ٳ   Ŀ   Ŀ   Ŀ   ڿڿ 
                 Ŀ                 ٳ  
                     Ŀ     Ŀ           
             Ŀ                 
                  



Wijckel, September 1997


                   Second part is english language.



Vanaf release 3.50 van INTERCOM is deze versie bijgevoegd die van een 
speciaal voor INTERCOM ontwikkelde print gebruik maakt.
Op deze print bevinden zich de volgende delen:
Een analoog/digitaal converter om de binnenkomende signalen te sampelen.
Een stroomgestuurde sinusgenerator die de mark en space tonen kan geven.
Een aantal open-collector uitgangen om de tranceiver te bedienen.
Tevens zit op de print een automatische volume regelaar voor ontvangst.

Vereist is hiervoor het volgende:
1) Een PC met minimaal een 386DX / 40 MHz of 486DX / 33 MHz processor.
        Indien u de snelle compoort-versie van INTERCOM kunt gebruiken,
        is de PC ook geschikt voor deze uitvoering van INTERCOM.
        Gezien de hogere eisen aan de PC worden Hercules en EGA 
        bij de dac-uitvoering niet ondersteund.
2) Een vrij ISA-slot.
3) Adres 260 HEX vrij
        Dit adres ligt in het gebied van de soundkaarten, die zich echter
        meestal op adres 220 HEX en soms op 240 HEX bevinden.
        Ook sommige netwerkkaarten maken van dit adresgebied gebruik.
        Eventueel de sound- of netwerkkaart een ander adres geven.
4) Ruime financile middelen ;-)

Gebruik van deze print heeft de volgende voordelen:
1) Het filteren van de tonen kan beter, immers het zgn. Hamcommodem maakt
   een blokgolf van de ontvangen audio, wat overeenkomt met 1-bits sampeling.
   Op deze interface wordt een signaal met 8 bits gesampeld.
   En het verschil tussen een blok en een sinus is toch weer 3 dB.
2) Het opwekken van de tonen gebeurt met een sinus-generator, zodat dit 
   direct aan de tranceiver gekoppeld kan worden.
   Dus geen filters meer die de ene toon sterker doorgeven dan de andere.
3) Zowel de PTT als de key ingang worden bediend omdat meerdere 
   schakeluitgangen beschikbaar zijn.
4) De compoort is weer vrij voor andere toepassingen.

De print wordt geleverd met een op maat gemaakte afdekplaat voor Fl 75,-
In euro's: Eu 35,-
Dit is dan een dubbelzijdige doorgemetaliseerde print, 
geboord, gelakt en met opdruk.
Dit is inclusief BTW, exclusief verzendkosten.

De overige onderdelen zijn in het hobbycircuit goed verkrijgbare 
I.C.'s en klein materiaal.
Zo ben ik er tenslotte zelf ook aan gekomen HI.
Helemaal onderaan na de engelse tekst is een onderdelenlijst opgenomen.

Mocht U andere toepassingen voor deze print willen bedenken,
de file dacscope.bas is een voorbeeld hoe eenvoudig de print
te benaderen is voor software.
Dit is in qbasic geschreven.

Mocht het zover komen dat U de print in de computer hebt zitten,
neem dan de regel: [DRIVE:\][DIRECTORY\][SUBDIRECTORY\]INTERCOM /S
in de autoexec.bat op.
Dit zorgt dan namelijk dat de print in een gedefinieerde toestand
komt en niet door uw microfoonsignaal gaat zitten fluiten.

Voor nadere informatie kunt U mij bereiken op de in INTERCOM.TXT 
aangegeven wijze.
Intekenen voor de print kan op het antwoord formulier ANTWOORD.FRM

Deze files behoren bij het deel interdac.lzh te weten:

        # INTERCOM.COM          het programma
        # INTERDAC.TXT          deze file
        # BOUWNDAC.TXT          file met uitleg en onderdelenlijst
        # INTERSET.EXE          hulpprogramma voor het afregelen van de print
        # DACSCOPE.BAS          voorbeeld file programmeren interface
        # INTERPCB.JPG          Afbeelding van de onbestukte intercom print
        # INTERCOM.ICN          extra icon alleen voor DAC versie, om te 
                                benadrukken dat vloeiende analoge vormen
                                te verkiezen zijn boven digitale.....

Interdac.lzh maakt deel uit van het totale pakket INTCOM40.LZH
en hoort alleen met dit totale pakket doorgegeven te worden.

******************* EINDE NEDERLANDSE TEKST *********************************







Starting with release 3.50 of INTERCOM this version is added which uses 
a PCB, specially designed for INTERCOM.
On this PCB you find the following:
An analog/digital converter to sample the incoming signals. 
A current-controlled generator which can give the mark and space tones.
A number of open-collector outputs to control the tranceiver.
Also on this print is an automatic volume controller for receiving.

For this is needed:
1) A PC, minimal 386DX / 40 MHz or 486DX / 33 MHz processor.
        If you use the fast comport-version of INTERCOM, your PC is 
        suitable for this version of INTERCOM.
        Because of the higher demands on the PC Hercules is not supported.
2) A free ISA-slot.
3) Free Adress 260 HEX
        This adres lays in the area of the soundcards, which usually are
        at adress 220 HEX and sometimes at 240 HEX
        Also some networkcards use this adress-area.
        If neccesary you have to put the sound- or networkcard 
        at an other adress.
4) Sufficient financial means ;-)

The use of this PCB does have the following advantages:
1) The filtering of the tones improves, ie. the so called Hamcommodem
   converts the incoming signals to a square wave, equals to 1-bits sampling.
   At this interface the sampling is 8-bits.
   And the difference between a square wave and a sinus is 3 dB.
2) The generating of the tones is directly a sinus, therefore it can be
   coupled directly to a tranceiver.
   No more filtering and different strengths of mark and space tones.
3) Both the PTT and the keying input are controlled, because different
   switching outputs are available.
4) You free the comport for other purposes.

This print is available with a tailored bracket
for the price of 75,- dutch gilders/ 35 Euro.
IE. a double sided metalized PCB, drilled with solder-mask and printing.
This is including Dutch VAT, without postage and handling.

The other parts are at the hobby-store easy-to-get I.C.'s and little parts.
After all, that is how i have got them HI.
At the bottom i have added a parts list.

If you want to use this PCB for other purposes,
the file dacscope.bas is an example how to simple it is to acces this 
PCB by other software.
It is written in qbasic.

If you do have this PCB in your computer,
add the line: [DRIVE:\][DIRECTORY\][SUBDIRECTORY\]INTERCOM /S
into your autoexec.bat.
This takes care of putting the PCB into a defined situation
and prevents it from starting to whistle into your mike.

If you want more information, i can be accessed at the way 
described in the INTERCOM.TXT file.

These files belong to the part interdac.lzh:

        # INTERCOM.COM          the program
        # INTERDAC.TXT          this file
        # BOUWNDAC.TXT          file with explanation and final parts list
        # INTERSET.EXE          helpprogram for adjusting the pcb
        # DACSCOPE.BAS          example file programming the interface
        # INTERPCB.JPG          Picture of the intercom print without parts
        # INTERCOM.ICN          additional icon for the dac version only,
                                to emhasis that curvy analog lines are 
                                preferrable above digital.....

Interdac.lzh is part of the total package INTCOM40.LZH
and should only be passed trough with the total package.


These are the parts i used on the PCB:

ELECTRONIC:
    6  CERAMIC CAPACITOR
    4  ELECTROLYTIC CAPACITOR
    16 RESISTORS 1/4 WATT
    2  MULTITURN CERMET TRIMMER
    1  JUNCTION FET 2N3819
    1  TRANSISTOR BC 108 C
    2  DIODE 1N4148
    1  82C55 COMMUNICATIONS INTERFACE
    1  TTL I.C. DM7407N
    1  TTL I.C. DM74LS74AN
    1  HCT I.C. 74HCT04N
    1  HCT I.C. 74HCT30N
    1  HCT I.C. 74HCT32N
    1  A/D ZN449E or ZN427E
    1  D/A ZN429E or ZN426E
    1  QUAD OPAMP TL084
    1  FUNCTION GENERATOR XR2206CP
    1  TIMER I.C. 555 C-MOS

HARDWARE:
    1  EXPANSION SLOT COVER
    1  15-POL D-SOCKET EMI/RFI SHIELDING
    1  15-POL D-PLUG FILTERED 90
    1  SHIELD FOR 15-POL D

And a piece of cable to connect it to my tranceiver.
